位置>千里马招标网> 招标中心> 【物资类】中国电建电建核电公司伊拉克鲁迈拉项目部控制电缆(增补)材料采购项目...
您尚未开通该权限!
咨询客服:400-688-2000,掌握更多商机线索!
- 咨询:400-688-2000查看全部商机
【物资类】中国电建电建核电公司伊拉克鲁迈拉项目部(增补)材料采购项目邀请书
1 ??总 则
1 General
1.1 本招标文件适用于(略)面的技术要求。
The Bidding Documents are applicable to the Control & Instrumentation?Cable of the AL-Rum(略) Combined Cycle 730 MW Power Plant Project and they specify the technical requirements for the functional design, structure, performance, installation and test of the equipment.
1.2本技术规范书提出了最低限度的技术要求,并未规定所(略),投标方应提供一套满足本技术规范书所列标准要求的高质量产品及其相应服务。对高厂变及其配套设备安装地点所在国家有关安全、环(略)
The Technical Specification specifies only the minimum technical requi(略)not all technical requirements and appli(略)st(略). So, the Bidder shall provide one set of high-(略)products and corresponding services as required by the st(略)li(略)in the Technical Speci(略). The requirements of the mandatory safety and environmental protection standards of the country where the UAT and the support equipment thereof are installed must be met.
1.3 招标方在本招标文件中提出了最低限度的技术要求,并未规定所有的技术要求和适用的标准,投标方应提供(略)及其相应服务。
The Tenderer specifies the minimum technical requirements in the Technical Speci(略)instead of all technical requirements and applicable standards. The Bidder shall provide one set of high-quality pr(略)and corresponding se(略)as re(略) by the Bidding Documents and the standards listed.
如果投标方(略),那么招标方可以认为投标方提供的产品应完全符合本招标书的要求。如有异议,不管(略),都应在差异表中提出。
If the Bidder has no objection to the provi(略)of the Bidding Documents in wr(略)form, the Tenderer may consider that the products from the Bidder should completely comply with the requirements of the Bidding Documents. In case of any obj(略)no ma(略) how small it is, it shall be presented in the list of deviations.
1.4 从签订合同之后至投标方开始制造之日的这段时期内,招标方有权提出因规程、规范和标准(略)遵守这些要求,并不发生合同价格的变更。
Du(略)the period from the signing of the contract to the comme(略)of manufacturing by the Bidder, the Te(略)has the right to present some supplement and amendment requirements due to the ch(略)of procedures, specifications and standards, and the Bidder shall ob(略)such req(略) without changing the contract price.
1.5 本技术规范书所引用的标准若与投标方所执行的标准发生矛盾时,按较(略)。
In case of contradictions between the reference standards of the Technical Specif(略)and the executive standards of the Bi(略) the higher standards shall prevail.
1.6 投标方对成套系统设备(含辅(略))负有全责,即包括分包(或采购)的产品。分包(或采购)的产品制造商应事先征得招标方的认可,未经过招标方(略)。对于投标方配套的控制装置、仪表设备,投标方提供其供货范围内设备与第三方设备的(如DCS控制系统)的接口,提供相关硬件和图纸文件配合,直至接口(略)。
The Bidder shall take full responsibility for the co(略)set of systems and equipment (including auxiliary systems and equipment), including subcontracted (or purchased) products. The manuf(略)of the subcontracted (or purchased) pr(略)shall be accepted by the Tenderer in advance. The subcontractors not co(略)by the Te(略)shall not provide equipment for the Project. For the support control devices and instruments provided by the Bidder, the Bidder shall provide the interfaces between the equipment within the scope of supply and the third-party equipment (such as DCS control system) and pr(略)assoc(略) hardware and coordination drawings until the interface installation and commissioning is over.
1.7 投标方投标文件经技术澄清双方达成一致的内容与本技术规范书具有同等约束力,并作为订货合同的一部分具有同等法律效力。在协议签订后,各方按时交换资料,满足接口要求,满足各方设(略)。压力容器出厂时提供投标方当地技术监督部门合格证。
The contents of the bid documents of the Bidder that are agreed by both parties through technical clarification shall have the same bi(略)effect as the Technical Specification, and as a part of the order contract, they have the same legal effect as the order contract. After signing the agreement, each party shall exchange materials on time to meet the interface requirements and each party’s requirements for design and manufacturing progress. Pr(略) vessels shall be delivered with the certificate of conformity issued by the technical supervision department of the place where the Bidder is located.
1.8 本工程采用标识编码采用电厂标识系统编码标准。投标方提供的技术资料(包括图纸)和设备标识应有标识编码,具体标识要求由设计院提出,在设计联络会上讨论确定。
The power plant identification system coding standard is adopted for the identification coding for the Pr(略). There shall be identification codes on the technical materials (including drawings) and equipment identification provided by the Bidder. The project specific identification (KKS coding sy(略)) requirements shall be presented by Shandong Electric Power Engineering Consulting Institute Corp., Ltd. (SD(略)) and shall be determined through discussion at the de(略) liaison meeting.
本工程所有系统图中,图例符号需按照设计院提出的要求执行,具体标识要(略),在设计联络会上讨论确定。
The legend symbols in all the system drawings of the Pr(略)shall meet the requirements of SDEPCI. The specific identification requirements shall be presented by SDEPCI and shall be deter(略) through discussion at the design liaison meeting.
1.9 所有进口产品必须为原产地产品,并提供原产(略)。
All the imported products must be those from the place of origin and provided with certificate of origin, import & export customs dec(略) and certificate issued by local chamber of commerce.
设备采用的专利涉及到的全部费用均已包含在设备报价中,投标方保证招标方不承担有关设备专利的一切责任。
All expenses involved in the equipment patents have been included in the equipment offer. Therefore, the Bidder shall ensure that the Tenderer is exempted from any responsibility for equipment patent ri(略).
1.10 投标方的基本报价中应包含现场安装、调试、(略)提供3年运行备件(清单)作为选项报价。
The basic offer by the Bidder shall include the wearing parts required during field installation, commissioning and trial run and the spare operational parts re(略) for one year warranty. Such parts shall be provided with the list, and the Bidder shall provide the spare parts (list) required for three years of operation as the optional offer.
1.11 设备色标由招标方统一要求。
The equipment color codes shall be subject to the requirements of the Tenderer.
1.12 投标方提供的资料数据单位全部采用国际单位制。
All the data of the materials provided by the Bidder shall be measured in SI unit.
1.13 本工程供电电压等级6.6kVAC,400VAC,23(略),220VDC,110VDC。频率范围为47.5~52HZ。
The supply voltage le(略)of the Pr(略)are 6.6kVAC, 400VAC, 23(略) 220VDC and 110VDC, and the range of frequency is 47.5~52HZ.
2 工程概况和场地条件
Project Overview and Site Conditions
2.1 工程概况
Project overview
(略)MW。
(略) MW.
电厂厂地为冲击(略)。场地基本地震烈度为8度(0.2g),按照9度设防。土壤承载力特征值约为300kPa,探明地下含水层在7~8米,地下水和土(略)。
The Plant site is a flood plain which has been prelim(略)leveled. The basic se(略)intensity of the site is Degree 8 (0.2g), seismic?fortification?as Degree 9.The chara(略)value of bearing capacity of soil is 300 kPa, and the pr(略) underground aquifer is at 7~8 meters. The underground water and the soil are corrosive.
2.2气象特征
Meteorological features
主要气象条件(****~****):
Main meteorological conditions (****~****):
平均温度:(略)
Average temperature: (略)
平均气压:(略)
Average air pressure: (略)
最大风速:(略)
Maximum wind speed: (略)
极端最高温度:(略)
Extreme maximum temperature: (略)
极端最低温度:(略)
Extreme minimum temperature: (略)
设计温度:(略)~50℃
The project design temperature: (略)
最低相对湿度:(略)
Minimum relative humidity: (略)
最高相对湿度:(略)
Maximum relative humidity: (略)
2.2.2 安装地点污秽等级:IV级,设备外绝缘爬电比距不小于3.1c(略)(按系统最高运行线电压为基准)
Pollution grade of installation place: Grade IV. The specific creepage distance of the external insulation for the equipment shall not be less than 3.1 cm/kV (the maximum operating line voltage of the system shall prevail).
2.3设(略)
Design and Operating Conditions
低压系统概况
系统标称电压: (略)
系统额定频率: (略)
系统中性点接地方式:(略)
Low Voltage System
System Nominal Voltage: (略)
System rated frequency: (略)
System neutral-point grounding mode: (略)
安装地点:(略)
Installation location: (略)
安装方式:桥架、、穿管
Installation methods: cable tray, cable trench, pipe-through
3 ??(略)
Standards and Specifications
3.1合同设备包括投标方及其下级供货商的所有附件和设备,全部设备应符合相应的标准规范或法规的最新版本或其修正本的要求, 除非(略),将包括在投标期内有效的任何修正和补充。
The contract eq(略)shall include all the access(略)and equipment of the Bidder and the sub-suppliers and shall comply with the requirements of the la(略)ed(略)or revision of relevant standards, specifications or regulations. Unless otherwise specifi(略)latest edition or revision shall incorpo(略)any valid corre(略) and supplement within the bidding period.
3.2除非合同另有规定,均须遵守最新的中国国家标准(GB)和国际电工委员会(IEC)标准以及国际单位制(SI)标准。如采用合资或**产品,还应遵守伊拉克国家标准,当上述标准不一致时按高标准执行。
Unless otherwise specified in the contract, the la(略) Chinese national standards (GB), International Electrotechnical Commission (IEC) standards, and International System of Units (SI) standards shall be observed. If joint products or collaborative products are adopted, the Iraqi national standards shall also be observed. In case of contradictions among such standards, the higher one(s) shall prevail.
所有螺栓、双头螺栓、螺纹、管螺纹、螺栓夹及螺母均应遵守国际标准化组织(ISO)和国际单位制(SI)的标准。
All bolts, studs, threads, pipe threads, bolt clips and nuts shall comply with the standards of the International Organization for Sta(略) (ISO) and the International System of Units (SI).
3.3 应遵循的(略)
Main current standards to be ob(略)
供方提供的设备应符合但并不仅限于以下现行标准(以最新版本为标准):
The equipment, provided by the Supplier, shall comply with but is not limited to the following current standards (the latest edition shall prevail):
GB156 ???《标准(略)
GB156 ??????????Standard Voltages
GB/T ****???????《电缆的导体》
GB/T **** ??Conductors of insulated cables
GB/T **** ??????《》
GB/T **** ???????Protective coverings for electric cable
GB/T **** ??????《电性能试验方法》
GB/T **** ???????Test methods for electrical properties of electric cables and wire
GB/T **** ?????《阻燃和耐火电线电缆通则》
GB/T **** ?????Flame retardant and fire re(略) wires and cables
GA 306 ????????《阻燃及耐火电缆塑料绝缘阻燃及耐火电缆分级和要求》
GA 306 ?????????Flame retardant and fire resistive cables- Classification and requirement for flame retardant and fire resistive characteristics of pl(略)in(略) cables
其它未明确(略),投标方也要遵守。
The bidder sh(略)also comply with other power industry standards which were not li(略) in this specification.
以上所列国家标准,投标方在技术协议签订后提供相应的英文版本。
For the China Standards mentioned above, bidder shall provide the corresponding English version after si(略) the technical speicification.
3.4 当标准(略),投标方应将矛盾情况提交用户,以便在开始生产前制定解决方案。
The Bidder shall su(略)the contra(略) among the standards and specifications (if any) to the user so that a solution can be made before the commencement of manufacturing.
4技术条件
Technical Spec(略)
4.1电缆(控制电缆、计算机电缆及热电偶补偿电缆)
Cable (control ca(略)Instrument cable and the(略) compensating cable)
阻燃控制电缆、阻燃控制屏蔽电缆、阻燃计算机电缆、阻燃计算机屏蔽电缆的性能应符合GB****.5标准(C类阻燃性能)要求。成品电缆芯线间,芯线与屏蔽间应经受交流50HZ,电压3kV,5min交流耐压试验,并应通过IEC****-3《电线电缆成束燃烧试验》的要求。电缆不应有抽芯和接头现象发生,电缆导体材质的电阻率、绝缘电阻、绝缘厚度以及屏蔽等各项性能应符合最新的国家标准。
(略) (Class C flame retardant performance). The core and shield of finished cables shall undergo AC withstand voltage tests of 50HZ, 3kV and 5min, and shall pass the requirements of IEC(略) Combustion test for mounted bunched wired or cables ". Cables should not have core pulling and joint. The resistivity, insulation resistance, insulation thickness and shielding properties of cable conductors should meet the latest national standards.
4.1.1运行温度及安装要求
Op(略)Temperature and Installation Requ(略)
电缆最高工作环(略):+105℃(耐高温电缆+260℃),最低环境温度:-40℃。导体的最高持续运行温度为90℃。投标方提供的电缆应满足以上电缆运行温度,否则应无条件退换货。
The hi(略)working envi(略)temp(略)of the cable is +105℃?(+260℃?for High Tempera(略)Resistant Cable) and the lowest wo(略)environment tem(略)is -40℃. The ma(略)continuous operating tem(略)of the co(略)is 90℃. The cable provided by the bidder shall meet the above requirements of operating temperature otherwise the ca(略) shall be returned and exchanged unconditionally.
投标方提供的电缆应能适用于户内和户外安装:空气中明敷,电缆托架内,导管内,地下混凝土钢管或塑料管排管内,地下沟道和直埋。尤其在电缆桥架、竖井和电缆沟(略)于电缆的拉力和侧压力。
The cable provided by the bidder shall be suitable for (略) installation: open laying in air, cable tray, conduit, underground concrete steel pipe or plastic pipe row, underground cable trench and direct burial. Especially when laying in cable tray, shaft and cable trench, it should be able to withstand the tension and lateral pressure acting on the cable when laying under the standard bending radius.
4.1.2电缆结构
cable st(略)
所有控制电缆、计算机电缆、补偿电缆和电源电缆线芯材质均为铜导体,计算机电缆线芯采用7股铜导体绞合结构(满足GB/T ****-****或IEC ****:****要求),其余电缆采用单股铜芯结构,所有电缆均为C级阻燃,投标方提供的有电缆的阻燃特性至少应符合IEC****-3C类电缆要求。耐火电缆要求为A级,即耐火试验供火温度为950~****℃,作用时间1.5h。电缆屏蔽层选用铜丝编织(铜丝编织密度不小于80%),计算机电缆采用分屏加总屏,控制电缆采用总屏。每根电缆的每一芯导线中间没有接头,所有电缆具有较好的电气性能,机械物理性能以及不延燃性,所有性能及线径误差满足有关国家规范和标准。
All I&C control ca(略)instrument cables, compensating cables and power cable cores are made of copper,the cable cores of instrument cables?are 7-(略)twisted copper conductor and the cable cores of?other cables are single-strand copper cores,?all ca(略)are class C flame retardants. The flame retardant prope(略)of cables provided by bidders shall at least meet the requirements of IEC****-3C cables. The requirement of fire-resistant cable is grade A, that is, the temperature of fire supply in refractory test is 950 ~ ****℃, and the working time is 1.5h. The shielding layer of the cable is braided with copper wire (the braided density of copper wire is not less than 80%). The cable shielding layer of instrument cable adopts the structure of total sh(略)layer and branched shielding layers, and the control cable adopts total shielding layer. There is no joint in the middle of each core conductor of each cable. All cables have good electrical properties, mech(略)and physical proper(略)and non(略). All per(略) and line diameter errors of cables should meet relevant ?national standards.
4.1.3电缆导体(缆芯)
cable conductor (cable core)
所有导体除热电偶补偿导线外应按照IEC ****规定。热电偶补偿线导线为实心,导体(略)MC96.1。 投标方应提供导体护层(略)蔽层。
All conductors except thermocouple compensating conductors shall comply with IEC ****. The conductor of thermocouple compensating calbe is solid, and the conductor ma(略)shall co(略)with ANSI MC96.1. Measures such as conductor shield should be provided to ensure that conductors can peel off the insulating layer or conductor sh(略) layer cleanly.
4.1.4绝缘和衬垫(内部覆盖和填充)
Insulation and gaskets (internal coverage and filling)
阻燃电缆的绝缘应为高质量、不延燃。多芯电缆应有衬垫,衬垫(略)。
Insulation of flame-retardant cable should be high-quality, no(略)sp(略).Multi-core cables should have gaskets that adopt high temp(略) resistant materials.
电缆(略)
Parameter require(略)for ca(略)
1、控制电缆
Control cable
交流额定电压:Uo/U 450/750V,耐压试验****V,5分钟完好;
工作温度:不高于+105℃。(耐高温电缆不高于+260℃);
最低环境温度:(略)
屏蔽控制电缆的屏蔽抑制系数≤0.05;
绝缘电阻:(略)
导体线芯直流电阻(20℃)符合 GB 39(略)60(略)
铜芯导体线芯1.5mm2;
外护套为灰色;
无铠装电缆允许弯曲半径不小于电缆外径的6倍, 铠装电缆允许弯曲半径不小于电缆外径的12倍。AC rated voltage: Uo/U 450/750V, intact withstand voltage test ****V for 5 minutes;
Working temperature: not higher than + 105℃. (High temperature resistant cable is not higher than + 260℃);
Minimum ambient temperature: (略)
The shielding suppres(略) coefficient of shielding control cable is less than 0.05.
Insulation resistance: not less than 105MΩ?m at 20℃;
The DC resistance of conductor core (20℃) conforms to GB****/IEC****.
Co(略) conductor core adopts 1.5mm2;
The color for Control and instrument cables will be gray.
The allowable bending radius of unarmoured cables is not less than 6 times of the outer di(略) of cables, and the allowable bending radius of armoured cables is not less than 12 times of the outer diameter of cables.
2、计算机屏蔽(仪表)电缆
Instrument shielded cable
模拟量信号的电缆为对绞分屏加总屏计算机电缆,用于热电阻的电缆均为三芯绞分屏加总屏计算机电缆;同样适用于单对对绞电缆。
交流额定电压:Uo/U 300/500V,耐压试验****V,1分钟完好。
屏蔽抑制系数≤0.01
电缆工作温度:不高(略)(耐高温电缆不高于+260℃);
最低环境温度:(略)
绝缘电阻:(略)
工作电容:(略)
电容不平衡:(略)
铜芯导体线芯1.0mm2;
无铠装电缆允许弯曲半径不小于电缆外径的6倍,铠装电缆允许弯曲半径不小于电缆外径的12倍;
每对绞或三芯绞应附有铜或铝Mylar屏蔽和镀锡绞合裸铜屏蔽线。单对屏蔽和屏蔽线与相邻对之间应绝缘;
每对绞或(略)
外护套为灰色。
Analog signal ca(略) are pair-twisted sub shielding and total shielding instrument cables, and the cables used for thermal resistance are three-core pair-twisted sub shielding and total shielding instrument cables.
AC rated voltage: Uo/U 300/500V, intact withstand voltage test ****V for 1 minute.
Shielding suppression factor ≤ 0.01.
The working temperature of the cable is not higher than +100℃?(High tempe(略) resistant cable is not higher than + 260℃).
Minimum ambient temperature: (略)
Insulation resistance: not less than 1x103MΩ?km at 20℃.
Working capacitance: (略)
Capacitance imbalance: (略)
The copper core conductor core is 1.0mm2.
The allowable bending radius of unarmed ca(略)is not less than 6 times of the outer diameter of ca(略) and the allowable bending radius of armoured cables is not less than 12 times of the outer diameter of cables.
Copper or aluminium Mylar shielding and tin-plated intertwisted bare copper shielding wires shall be at(略)to each pair of strands or three-core strands. The sh(略)and shielding wires of each pair should be insulated from that of ad(略) pairs.
Each pair of strands or three-core strands shall be twisted with interval of about 50 mm.
The cable outer sheath is?gray.
3、热电偶补偿电缆
Thermocouple compensating cable
用于热电偶信号的电缆均为对绞分屏加总屏补偿电缆。热电偶补偿电缆应采用密封绝缘和护套的工艺结构,应具有优良的防潮、防腐等性能,测量精度(略)。
电缆工作温度:不高于+70℃(略):不高(略)
最低环境温度:(略)
绝缘电阻:(略)
工作电容:(略)
电容不平衡:(略)
分布电感:(略)
静电感应电压(静电电压20KV):(略)
电磁干扰感应电压(50HZ,400A/m):(略)
无铠装电缆(略),铠装电缆允许弯(略)
电缆额定电压300V;
热电偶补偿线芯线材料应按照ANSI MC96. 1使用所要求的热电偶材料;
着色应按照ANSI MC96.1规定。
The cables used for therm(略)signals are pair-twisted sub shielding and total sh(略)compensation ca(略). Thermocouple compensating cables sh(略)adopt st(略)of se(略)insulation and sheath. The calbe should have excellent moisture-proof and ant(略)properties. The measurement ac(略)should meet the requir(略) of relevant national or international standards.
The working temperature of the cable is not higher than +70℃, and the working temperature of the high temper(略)compe(略) cable is not higher than + 200℃.
Minimum ambient temperature: (略)
Insulation resistance: not less than 25MΩ?km at 20℃.
Working capacitance: (略)
Capacitance imbalance: (略)
Distributed inductance: (略)
Electrostatic induction voltage (electrostatic voltage 20KV): (略)
Electromagnetic interference induced voltage (50HZ, 400A/m): (略)
The allowable bending radius of unarmed cables is not less than 6 times of the outer diameter of cables, and the allowable bending radius of armoured ca(略) is not less than 12 times of the outer diameter of cables.
The rated voltage of cable is 300V.
Thermocouple compensation cores and wires shall use the required thermocouple materials in accordance with ANSI ?MC96.1.
Coloring shall be in accordance with ANSI ?MC96.1.
4.2电缆型号说明
Cable type explanation
因各电(略),本工程的电缆型号(或代号)含义规定如下:
Because the cable models of various cable manufacturers are not the same, the meaning of the cable models (or codes) of this project is as follows:
4.2.1普通控制电缆:
For control cable
常规场合使用:ZC-KVVP(22)-0.45/0.75-N×1.5,2.5
N--电缆芯数=4,7,10,14,19,24
含义描述:ZC(略),KVVP--铜芯聚氯乙烯绝缘、聚氯乙烯护套(铜丝编织总屏蔽)控制电缆,(22) --铠装(仅直埋电缆使用),0.45/0.75--额定电压为0.45/0.75kV,电缆芯截面积:1.5。
For normal situation:ZC-KVVP(22)-0.45/0.75-N×1.5,2.5
N--cable core nu(略),7,10,14,19,24
ZC--flame retardant C level, KVVP--copper wire core with polyvinyl chloride insulation and sheath (co(略) wire braided total shield), (22)--armoured cable (only used for direct buried cables), 0.45/0.75--rated voltage is 0.45/0.75kV, 1.5--cross section area of cables core.
耐高温环境使用:ZC-KFFP(22)-0.45/0.75-N×1.5,2.5
N--电缆芯数=4,7,10,14,19,24
含义描述:ZC--阻燃C级,KFFP--铜芯聚全氟乙丙烯F46绝缘和护套(铜丝编织总屏蔽)控制电缆,(22) --铠装(仅直埋电缆使用)。0.45/0.75---额定(略).45/0.75kV;电缆(略):1.5。
For high tempe(略)enviro(略):ZC(略)(22)-0.45/0.75-N×1.5,2.5
N--cable core number=4,7,10,14,19,24
ZC--flame retardant C level, KFFP--copper wire core and FEP (F46) insulation and sheath (copper wire braided total shield), (22)--armoured cable (only used for direct buried cables) , 0.45/0.75--rated voltage is 0.45/0.75kV, 1.5--cross section area of cables core.
4.2.2计(略):
For instrument cable
常规场合使用:ZC-DJYPVP(22)-0.3/0.5-N×(n×1.0)
N--电缆芯(对)数=1,2,3,4,5,6,7,8(一般不超过 8);
n--每对电缆的芯数=模拟量电缆为2,热电阻电缆为3。
含义描述:ZC--阻燃C级,DJ--计算机电缆,(22)--铠装(仅直埋电缆使用),YPVP--铜芯聚乙烯绝缘、聚氯乙烯(PVC)护套,铜丝编织-分屏蔽加总屏蔽单股电缆,0.3/0.5--额定电压为0.3/0.5kV。
For normal situation:ZC-DJYPVP(22)-0.3/0.5-N×(n×1.0)
N-- Number of Cable Cores (Pairs)=1,2,3,4,5,6,7,8(no more than 8).
n-- cable core number of each pair =2 for analog cable, 3 for thermal resistance cable.
ZC--flame re(略)C level, DJ--co(略)cable, (22)--armoured cable (only used for direct buried ca(略)), YPVP--Copper core polyethylene insulation and polyvinyl chloride (PVC) sheath, individual pair shielded + total shielded braided with copper wire, 0.3/0.5--rated voltage is 0.3/0.5kV.
耐高温环境使用:ZC-DJYPVP(22)-105-0.3/0.5-?N×(n×1.0)
N-(略)(对)数=1,2,3,4,5,6,7,8(一般不超过 8);
n--每对电缆的芯数=模拟量电缆为2,热电阻电缆为3。
含义描述:ZC--阻燃C级,DJ--计算机电缆,(22)--铠装(仅直埋电缆使用),YPVP(略)(PVC)护套,铜丝编织-分屏蔽加总屏蔽单股电缆,105--最高工作温度105℃,0.3/0.5--额定电压为0.3/0.5kV。For high tem(略) environment:ZC-DJYPVP(22)-105-0.3/0.5-N×(n×1.0)
N-- Nu(略) of Cable Cores (Pairs)=1,2,3,4,5,6,7,8(no more than 8).
n-- cable core number of each pair =2 for an(略)cable, 3 for thermal resi(略) cable.
ZC(略)retardant C level, DJ--computer/instrument cable, (22)--arm(略)cable (only used for direct buried cables), YPVP--(略)core polyeth(略)insulat(略)and polyvinyl chloride (PVC) sheath, individual pair shielded + total sh(略) braided with copper wire, 105—the highest operating temperature is 105℃, 0.3/0.5--rated voltage is 0.3/0.5kV.
4.2.3热电偶补偿电缆
For thermocouple compensation cable
ZC-KX-HS200(22)-FP(略)(n×1.5)
N--电缆芯(对)数=1,2,3,4,5,6,7,8(一般(略))
n=2
含义描述:ZC--阻燃C级,KX--耐热用精密级K分度,HS200-(略),(22) --铠装(仅直埋电缆使用),FP(略)--聚全氟乙丙烯F46绝缘和护套,铜丝编织(略)。
ZC-KX-HS200(22)-FPF-2A-N×(n×1.5)
N--Number of Cable Cores (Pairs)=1,2,3,4,5,6,7,8(no more than 8)
n=2
ZC--flame retardant C le(略)KX--Precision grade K degree for heat resistance, HS--high temperature re(略)precision type, HS200--(略)highest retardant temperature for Long-term operating is 200℃, (22)--armoured cable (only used for direct buried cables), FPF-2(略) (F46) insulation and sheath, individual pair shielded + total shielded braided with copper wire.
4.2.4耐火控制电缆
Fire-(略) control calbe:ZCN-KVVP-0.45/0.75- N×1.5
N--电缆芯数=4,7,10,14,19,24
含义描述:ZCN--耐火,KVVP--铜芯聚氯乙烯绝缘、聚氯乙烯护套(铜丝(略))控制电缆,0.45/0.75--额定电压为0.45/0.75kV,1.5--电缆芯截面积。
N-(略)core nu(略),7,10,14,19,24
ZCN--Fire-resistant, KVVP--copper wire core with polyvinyl chloride insulation and sheath (copper wire braided total shield), 0.45/0.75(略)vo(略)is 0.45/0.75kV, 1.5--cross section area of ca(略) core.
4.2.5通信电缆
Communication?calbe:(略)
N--电缆对数=5,10,20,30,50,100
含义描述:ZR—阻燃,HYA--铜芯聚烯烃绝缘、聚乙烯护套(铜丝编织总屏蔽)市内通信电缆, 0.5--电缆芯截面积。
N--cable pair?number,5,10,20,30,50,100
ZR--F(略)HYA--(略)wire core with polyvinyl insulation and sheath (copper wire braided total sh(略)), 0.5--cross section area of cables core.
Communication?calbe:(略)
含义描述:ZR--阻燃,LA--铜芯聚烯烃绝缘、聚乙烯护套(铜丝编织总屏蔽)通信电缆,2×2.5+2×0.5--2芯2.5截面电源线+2芯0.5截面信号线。
ZR--Fire-resistant,LA--copper wire core with polyvinyl insulation and sh(略) (copper wire braided total shield), 2×2.5+2×0.5—2 core 2.5?section power wire + 2 core 0.5?section signal wire.
Communication?calbe:(略)
含义描述:HRVB--铜芯聚烯烃绝缘、聚乙烯护套电话线, 2×0.5--2芯2.5电缆芯截面积。
HRVB--copper wire core with polyvinyl insulation and sheath,2×0.5--2 core 0.5?section signal wire.
Communication?calbe:(略)
N--电缆芯数=2,4,10,14
含义描述:ZR--阻燃,BVV --铜芯聚氯乙烯绝缘、聚氯乙烯护套电缆,500-绝缘电压500V,2.5--电缆芯截面积。
N--cable core number=2,4,10,14
ZR--Fire-resistant, BVV--copper wire core with polyvinyl chloride insu(略)and sh(略)500-(略) voltage is 500V, 2.5--cross section area of cables core.
4.3其它要求
Other requi(略)
4.3.1电缆外护套表面每隔1米左右应有一个电缆生产厂家、型号规格、长度等标记,长度累计数码标记应每隔1米打一个数码。标记应清晰、耐摩擦并具有连续性。电缆端头应封堵严密。
The su(略)of cable sheath sh(略)be marked by a cable manufacturer, model specifications, length and so on every 1 meter or so. The accumulated length code should be marked by a number every 1 meters. Marking should be clear, friction resistant and continuous. Cable end sh(略) be sealed tightly.
4.3.2电缆线芯应以数字来识别,识别标志应清(略),应符合GB/(略)。控制电缆(略)。控制电缆芯线绝缘统一采用黑色,编码为白色。
Cable cores should be identified by numbers. The identification marks should be clear, friction-resistant and continuous. They should conform to GB(略)standard. The control cable insulated wiring core adopts coding partition by di(略)1,(略). The insulation of control cable core is uniformly black, and the core code is white.
4.3.3电(略)
Cable out-of-roundness
电缆不圆度不应大于(略)。
Cable out-of-roundness should not exceed (略)。
4.3.4电缆盘
Cable reel
电缆盘应采用铁(略),电缆盘应能承受在运输、现场搬运中可能遭受的外力作用。应能在任何气象条件下在户外至少储存5年期间可能遭受的外力作用。并且电缆盘应能承受在安装或处理电缆时所可能遭(略)小弯曲半径。每盘电(略)。
电缆装盘每盘必须是一根完整的电缆,配盘参照设计院最终电缆清册,由招标方、投标方在联络会确定。避免施工过程中出现电缆接头。
同一盘电缆中,不应有不同型号的电缆混装。
每盘电缆长度计量误差不超过±0.5%。
电缆盘外侧各项标记如电缆型号、规格、每段长度等应准确清晰。
电缆包装运输应按国标或国际要求执行。
Cable reel shall be made of iron and wood, and cable reel shall be able to withstand the external force that may be suffered during transportation and on-site handling. It should be able to store outdoors for at least five years under any we(略)conditions the external forces it may su(略). And the cable reel should be able to withstand the ex(略)force that may be suffered when installing or ha(略)the cable without damaging the cable and the reel body. The minimum diameter of the cable reel barrel body shall conform to the mi(略) bending radius of the cable. The end of each cable shall be sealed with a sealing head.
The cable installed on each cable reel must be a complete cable. The cable confi(略)refers to the final cable list supplied by the Design Institute and is deter(略)by the tenderer and bidder at the liaison me(略). Avoid cable joints during construction.
In the same cable reel, mixing different types of ca(略)is not al(略).
The length measurement error of each cable does not exceed ±0.5%.
The markings on the outer side of cable reel, such as cable type, specification and length of each section, should be accurate and clear.
Cable packaging and transportation shall be carried out in accorda(略)with the requirements of the na(略) or international standard.
4.3.5电缆的导体及导线表面均应光洁,不得有任何缺损。电缆应防潮(湿)、防油、防酸。铠装电缆(略),铠装的故障电流额定值应与芯线导体相同。
The co(略)of the cable and the surface of the conductor shall be sm(略)and clean without any defect. The cable should be damp-proof (wet), oi(略) and acid-proof. The armour of armoured cables shall be continuous and sealed galvanized steel strips. The rated fault current of armour shall be the same as that of core conductors.
5包装、运输要求及铭牌
5Package, transport req(略) and nameplate
5.1 ?投标方交付(略)和包装储运标志。?包装应保证在运输、装卸过程中完好无损,并有减振、防冲击的措施。?若包装无法防止运输、装卸过程中垂直、水平加速度引起的设备损坏,投标方要在设备的设计结构上予以解决。?包装应按设备特点,按需要分别加上防潮、防霉、防锈、防腐蚀的保护措施,以保证货物在没有任何损坏和腐蚀的情况下安全抵达合同设备安装现场。?产品包装前,投标方应按部套进行检查清理,不留异物,并保证零部件齐全。?
All the goods de(略)by the Bidder shall have solid packaging suitable for long-distance sea tran(略)multiple transportation and handling and packaging storage and transportation signs in accordance with China Na(略)Import& Export Commodity Inspection Bureau and the Specification. The package shall be undamaged and in good co(略)in transport, loading, and unloading pr(略)with vibration reduction and striking resistant me(略). To the extent that the packaging cannot prevent the equipment from being damaged due to vertical and horizontal acceleration in transport, loading, and unloading process, the Bidder shall consider structure design of the equipment. Mo(略)mildew and corrosion protection measures shall be taken respect(略)as required according to the features of equipment, to guarantee the goods can be safely transported to the installation site of co(略)equipment without any damage and corrosion. Prior to packaging, the Bi(略) shall inspect and clean the products by sets to guarantee the products are free from foreign matters and the parts are complete.
5.2 ?投标方(略)。?包装箱(略),并应标明招标方的订货号和发货号。?每件包装箱内,应附有包括名称、数量、图号的详细装箱单、合格证(中英文)。?外购件包装箱内应有产品出厂质量合格证明书、技术说明各一份(中英文)。?格式应以招标方提供的为主。?
The Bidder shall meet the req(略)in Packa(略)Pro(略)and Identification?procedure of the Tenderer. The pa(略)box shall have obvious packaging and tra(略)image marks with order No. of the Tenderer and delivery number. detailed packing list in(略)name, quantity and drawing number as well as Chinese-English descri(略)shall be included in each package. For purchased parts, one copy of Chinese-English factory quality certificate and technical spe(略)of product shall be included in the pa(略). The format shall conform the requirements from the Tenderer.
5.3 ?电缆在运输过程中,内部结构相互位置不变,紧固件不松动,并要求能承受3g的运输水平加速度。?
Du(略)the transportation of LV power cable, mu(略)position of in(略)structures shall not change and the fastener shall not loose.?Which is able to bear 3g horizontal acceleration from trans(略).
5.4 ?运输时低压电力电缆的所有组件、部件及备品备件、专用工具等不丢失、不损坏、不受潮和不腐蚀。
There is no loss, damage, damp or co(略)in all components, parts, spare parts, sp(略) tools and so on.
5.6 随产品提供的技术资料应完整无缺。
echnical data along with the pr(略) shall be complete and intact.
5.7凡由于投标方对货物的包装与标记或其提交的文件不符合(略)使船运/空运计划延误,应由投标方承担相应的责任。?
The Bidder shall assume the responsibilities if the goods package and marks or the documents provided by the Bidder fail to meet relevant provisions about exported equipment and this makes that the Tenderer can’t obtain export license including custom clearance and delay the shi(略) transportation plan.
5.8投标方所提供的货物和文件及其包装需运送至外国境内的,投标方应保证货物和文件及其包装符合当地海(略)
If the Bidder shall transport the go(略)documents and pa(略)outside Ch(略)the Bidder shall guarantee that go(略)do(略)and packages conform to relevant requi(略)from local customs and import ins(略) and quarantine.
5.9 设备标志
Equipment signs
1)各部套均有固定铭牌。?铭(略),铭牌上层标明型号、容量、制造厂名、出厂年月等重要参数。
Nameplate is not easy to damage. mo(略)capacity, manufa(略)name, prod(略)date and other important paramet(略)are marked on upper layer of the nameplate. Nameplate is not easy to damage. model, capacity, manufacturer’s name, produc(略)date and other im(略) parameters are marked on upper layer of the nameplate.
2) 重要部件根据图纸规定,在一定位置上标有装配编号,使用材料和检验合格的标志。
Important components shall be marked with assembly number, materials and passed inspect ion on ce(略)po(略)according to standards of dr(略).
5.10其他要求详见供货合同的商务部分。
See the Commercial Proposal of the Supply Contract for other requirements.
报价清单 | |||||||||
序 号 | 物资名称 | 规 格 | 型 号 | 单 位 | 数 量 | 单 价 (元) | 总 价 (元) | 备 注 | 物 资 编 码 |
1 | 控制电缆Control Cable | ZC-DJYPVP-0.45/0.75?? | 4*2*1.0 | 米 | 56 | ||||
2 | 控制电缆Control Cable | ZC-DJYPVP-0.45/0.75?? | 8*2*1.0 | 米 | 21 | ||||
3 | 控制电缆Control Cable | ZC-DJ(略).3/0.5?? | 4*2*1.0 | 米 | 169 | ||||
4 | 控制电缆Control Cable | ZC-KVVP22-0.45/0.75 | 7*4 | 米 | 76 | ||||
5 | 控制电缆Control Cable | ZCN-DJYPVP-0.3/0.5?? | 2*2*1.0 | 米 | 29 | ||||
6 | 控制电缆Co(略) Cable | ZCN-DJY(略).3/0.5?? | 3*2*1.0 | 米 | 31 | ||||
7 | 控制电(略) Cable | ZCN-DJ(略).3/0.5?? | 4*2*1.0 | 米 | 62 | ||||
8 | 控制电缆Control Cable | ZCN-DJYPVP22-0.3/0.5 | 2*2*1.0 | 米 | 198 | ||||
9 | 控制电缆Control Cable | ZCN-DJYPVP22-0.3/0.5 | 3*2*1.0 | 米 | 322 | ||||
10 | 控制电缆Control Cable | ZCN-DJYPVP22-0.3/0.5 | 5*2*1.0 | 米 | 68 | ||||
11 | 控制电缆Control Cable | ZCN-KVVP22-0.45/0.75 | 10*1.5 | 米 | 198 | ||||
12 | 控制电缆Control Cable | ZCN-(略).45/0.75 | 14*1.5 | 米 | 62 | ||||
13 | 控制电缆Control Cable | ZCN-KVV(略).45/0.75 | 4*1.5 | 米 | **** | ||||
14 | 控制电缆(略) Cable | ZCN-KVVP22-0.45/0.75 | 4*2.5 | 米 | **** | ||||
15 | 控制电缆(略) Cable | ZCN-KVVP22-0.45/0.75 | 4*4 | 米 | 81 | ||||
16 | 控制电缆Control Cable | ZCN-KV(略).45/0.75 | ?5*4 | 米 | **** | ||||
17 | 控制电缆Control Cable | ZCN(略).45/0.75 | 7*2.5 | 米 | **** | ||||
金额合计 | 元 | ||||||||
偏差请在报价单中注明,仅提供报价单即可 | |||||||||
技术服务、保证措施和服务响应时间: | (略) | ||||||||
其他优惠条件及承诺: | 报价单位:??????????????????????? (盖章) | ||||||||
联 系 人: | |||||||||
联系方式: | |||||||||
报价时间:???????? 年?????? 月?(略) 日 |
关注“电缆宝”公众号
免费获取海量采购、招标、现货、线缆价格最新信息
采购招标 | 现货市场 | 厂商报价
注册会员享贴心服务
项目查询服务
·让您全面及时掌握全国各省市拟建、报批、立项、施工在建项目的项目信息
·帮您跟对合适的项目、找对准确的负责人,全面掌握各项目的业主单位、设计院、总包单位、施工企业的项目经理、项目负责人的详细联系方式
·帮您第一时间获得全国项目业主、招标代理公司和政府采购中心发布的招标、中标项目信息
项目定制服务
·根据您的关注重点定制项目,从海量的项目中筛选出符合您的要求和标准的工程并及时找出关键负责人和联系方式
·根据您的需要,向您指定的手机、电子邮箱及时反馈项目进展情况
- 猜你喜欢
- 更多平原县招标采购信息
- 华西十二公司四分公司金牛宾馆(改)
- 12月13日
- 彩色便道砖、水磨石地板砖
- 12月13日
- 竞争性磋商公告甘肃省张掖市公路工程
- 12月13日
- 给水管材
- 12月13日
- 废轴承
- 12月13日
- 2019年12月份矿用电缆二12.
- 12月13日
- (XJ019121300031)冲
- 12月13日
- 山西国金电力有限公司发电项目202
- 12月13日
- 铁
- 12月13日
- 江苏徐塘圆顶阀密封圈等询价采购询价
- 12月13日
- 废膜
- 12月13日
- 南京电厂调心滚子轴承等物资询价结果
- 12月13日
-
平原县建材网
平原县采购信息网
平原县政府公开信息
平原县公共资源交易网
平原县电力交易中心
平原县交易中心
平原县房产交易中心
平原县工程交易中心
平原县钢铁交易中心
平原县建设交易中心
平原县招投标交易中心
平原县政府交易中心
平原县造价信息网
平原县市政工程信息网
平原县水利工程信息网
平原县通信工程信息网
平原县医药招标网
平原县建筑招标网
平原县工程招标网
平原县建设招标网
平原县施工招标
平原县装饰工程招标
平原县建设工程网
平原县水利招标信息网
平原县电力招标网
平原县建委招投标网
平原县建筑管理网
平原县建设信息港
平原县教育招标网
平原县装修招标
平原县人力和社会保障局
平原县建设网
平原县总包工程
平原县政府工程招标
平原县工程施工招标
平原县工程公开项目
平原县工程采购信息
平原县招标投标采购平台
平原县省市工程建设网