开启全网商机
登录/注册
橡胶制品
招标详情
下文中****为隐藏内容，仅对千里马会员开放，如需查看完整内容请
「注册/登录」或 拨打咨询热线：
400-688-2000
| 招标单位 | 板带事业部 | 项目名称 | 橡胶制品 |
| 招标邮箱 | zhaobiao@nanshan.****.cn | 联系人及电话 | 王经理、马经理155****8610、185****0206 |
| 质保期 | 报名截止日期 |
| 项目保证金 | 10000.00元 | 账户名称 | **新南****公司 |
| 账号 | 233****12142 | 开户行 | 中国银行****支行 |
| 备注 | |||
| 备注：竞价****公司转账，不支****银行柜台现金转账。 | |||
| 标书联系人 | 无 | 办公电话 | 无 |
| 邮件 | 无 |
| 账户名称 | 无 | 账号 | 无 |
| 开户行 | 无 | 行号 | 无 |
| 标书收费标准 | 地址、电话 | 无 | |
| 备注：****公司转账，不支****银行柜台现金转账。注明标书费的用途或投标项目名称。 | |||
| 耐油橡胶板 | 1200mm*5mm | 25.00 | 千克 | {"规格型号":"1200mm*5mm","厚度":"5mm","宽度":"1200mm","材质":"橡胶（纯胶胶板）","耐油性能":"C类（耐油）（#3标准油，100℃×72h）（对应的体积变化率ΔV/% ：-5~+40）","硬度要求":"H5","抗撕裂性能":"Ts（抗撕裂）","拉断强度":"拉断伸长率≥200％","拉伸强度":"≥5MPa","使用寿命":"流程性消耗品（实际寿命因运行参数和周围环境及使用状态而定）天","特殊要求":"热空气老化性能：Ar2；设备介质最高温度：80℃；表面状态：平板光面,不允许有开裂、穿孔等影响使用性能的缺陷；接触介质：油+水；长度：不限定，但必须保证最短的一张长度不得低于1200mm","参照标准":"GB/T 5574-2008","备注":"厚度偏差5±0.5mm，宽度偏差1200±20mm；零部件供货时提供到货清单+合格证（所用材质的耐油性能，必须在合格证或在另外附加的材质证明上体现。）；如有特殊使用要求或说明则应在合格证上标明或附带说明书等资料。到货与本技术要求不符，厂家无条件免费退换货。"} |
| 氟橡胶O型密封圈 | 243*232*5.5 | 10.00 | 个 | {"规格型号":"243*232*5.5","内径":"Φ232mm","外径":"Φ243mm","丝径":"Φ5.5mm","材质":"氟橡胶","硬度要求":"硬度60±5","工作温度":"0-160℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"要求：产品表面要光洁、无凹坑、无飞边，耐油、耐高温、耐酸碱、密封性好，弹性好。产品运输，贮存过程中应防过度挤压、碰撞，产品性能达不到要求，厂家无偿退换货，产生的费用由厂家自行承担"} |
| 高压软管 | 51*1*4 | 6.00 | 根 | {"型号":"51*1*4","图号":"无","材质":"胶管材质为耐油合成橡胶","接头材质":"无接头","接头尺寸":"无接头","接头形式":"无接头","长度":"1.7±0.2m","压力":"4Mpa","所属设备名称":"熔炼炉","设备型号":"90T","设备生产厂家":"布里克蒙","国产/进口":"进口","使用寿命":"730天","特殊要求":"公称内径:51mm,1层钢丝缠绕,介质:液压油,环境温度:-20~60℃","参照标准":"GB/T 3683-2011","备注":"验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} |
| 胶管总成 | 4-19*46*3000 | 18.00 | 根 | {"型号":"4-19*46*3000","材质":"材质：丁腈橡胶，外包304不锈钢钢编，螺母、法兰材质：碳钢","内径":"Φ19mm","外径":"Φ27mm","高度":"3000mm","颜色":"钢编管","使用介质":"液压油","工作压力":"24Mpa","参照标准":"JB/T 8727-2017","备注":"接口形式：一直头φ38圆形法兰带O型圈，一90°弯头螺母φ20喇叭口，通径：19mm；耐压：24Mpa；4层钢编；连接螺母：M27*2.0；长度：3000mm，使用寿命：2年，不符合要求，供货厂家免费退换货"} |
| 胶管总成/熔保炉液压站循环泵 | 3-25*1500 | 6.00 | 根 | {"型号":"3-25*1500","材质":"材质：内胶层：耐油合成橡胶；中间3层高强钢丝钢编，外胶层：耐腐蚀合成橡胶；接头材质：碳钢","内径":"Φ25mm","外径":"Φ35mm","高度":"1500mm","颜色":"黑色","使用介质":"液压油","工作压力":"13Mpa","参照标准":"JB/T 8727-2017","备注":"公称通径25mm，工作压力13Mpa，工作介质：液压油，工作温度：-10℃-80℃，两端直头螺母1-5/16” *12牙扩口，长度1500±100mm，使用寿命3年，到货后不符合要求免费退换货"} |
| 胶管 | Ф65 | 4.00 | 米 | {"型号":"Ф65","图号":"无","材质":"丁腈橡胶,内一层绳芯","接头材质":"无接头","接头尺寸":"无接头","接头形式":"无接头","长度":"65±3mm","压力":"1Mpa","所属设备名称":"扒渣车","设备型号":"10M","设备生产厂家":"意大利泰克莫","国产/进口":"进口","使用寿命":"730天","特殊要求":"无接头;耐温:60℃","参照标准":"GB/T 3683-2011","备注":"验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} |
| HF型高压测压软管 | HFH2-P2-3-P-1000 | 3.00 | 根 | {"型号":"HFH2-P2-3-P-1000","规格尺寸":"软管一端快接式接头，快式接头螺纹为M16*2.0mm，另一端直接接表计，其螺纹为M20*1.5mm，软管公称通径3±0.2mm，总长度1000±5mm，软管外径6±0.5mm","颜色":"黑色","配套参数":"静态压力不小于40MPa，最小爆破压力63MPa","使用温度":"-40~120℃","产品材质":"管子材质：内芯耐压、耐油聚酰胺12，编织层为芳纶纤维编织;连接头材质：镀锌铁","参照标准":"GB/T 3683-2011","备注":"进口/国产信息：国产，使用寿命：2年，验货标准：1、技术参数与要求不符时，供应商应给予更换或退货。2、由于产品升级导致型号不一致，但技术参数满足现场使用要求，由厂家出具相关证明，方可办理入库。"} |
| HF型高压测压软管 | HFH2-P1-3-P-1000 | 10.00 | 根 | {"规格型号":"HFH2-P1-3-P-1000","材质":"内芯为耐压耐油聚酰胺,编织层为芳纶纤维,接头材质为镀锌碳钢","所属设备名称":"引风机稀油站","设备型号":"GDYZ-100","设备生产厂家":"****公司","使用寿命":"730天","特殊要求":"软管一端为快接式插头,接口螺纹M16*2.0mm,另一端直接接压力表,接口螺纹M14*1.5mm"} |
| 高压软管 | 4SHA32*19300 | 2.00 | 根 | {"型号":"4SHA32*19300","图号":"****7897","材质":"四层钢丝编制液压橡胶管","接头材质":"碳钢","接头尺寸":"M52*2","接头形式":"24°锥密封，接头为A型","长度":"19300mm","压力":"350bar","所属设备名称":"双机架冷轧机","设备型号":"2500mm","设备生产厂家":"西马克","国产/进口":"国产","使用寿命":"730天","特殊要求":"由于长期浸泡在轧制油中，要求软管和密封有良好的耐轧制油腐蚀和阻燃性。到货验收：物质不满足技术要求退换货处理；退换货产生的费用由供货商承担。","参照标准":"SN 756-2007"} |
| 橡胶管 | DN63*10000 | 1.00 | 根 | {"型号":"DN63*10000","材质":"耐油橡胶","内径":"Φ63±1mm","外径":"Φ79±1mm","高度":"10000mm","颜色":"黑色","使用介质":"轧制油、煤油","工作压力":"1.2Mpa","参照标准":"GB/T 15329-2019","备注":"1.长度10米/根，耐油、耐酸。2.验收标准：到货与技术要求不符时，供应商无条件退换货处理，所产生费用由供货商承担。3.使用寿命：≥365天。"} |
| 缓冲垫 | Φ56*30*14mm | 200.00 | 个 | {"规格型号":"Φ56*30*14mm","外径":"56mm","内孔直径":"30mm","厚度":"12mm","瓣数":"0","爪瓣形状":"无","材质":"聚氨酯","使用寿命":"＞180天","参照标准":"GB/T 5272-2017","备注":"到货外观应无破损、划痕，随货附带产品合格证，材质报告，与技术要求不符时厂家给予退换货处理。"} |
| 油封 | 80*100*12 | 10.00 | 个 | {"规格型号":"80*100*12","内径":"Φ80mm","外径":"Φ100mm","高度":"12mm","骨架材质":"铁骨架","密封材质":"丁晴橡胶/氟橡胶","结构形式":"外骨架单唇形","工作温度":"-20℃—100℃℃","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"验收标准：验收标准：到货外观应无破损、划痕，随货附带产品合格证，材质报告，与技术要求不符时厂家给予退换货处理。"} |
| PVC钢丝增强软管 | DN25*3 | 50.00 | 米 | {"规格":"DN25*3","连接形式":"管箍固定","工作温度":"≤70℃","工作压力":"0.1Mpa","壁厚":"3mm","内径":"Φ25mm","外径":"Φ31mm","参照标准":"GB/T 9574-2017","备注":"使用寿命：365天；验收标准：提供产品合格证，若产品不符合技术要求，予以免费退货更换。"} |
| 胶管 | NB50*2000 | 2.00 | 根 | {"型号":"NB50*2000","材质":"二层钢丝缠绕橡胶软管","接头材质":"碳钢","接头尺寸":"G2","接头形式":"平头","长度":"2000mm","压力":"16bar","国产/进口":"国产","使用寿命":"365天"} |
| 挡圈 | 260*270*1.9 | 56.00 | 个 | {"规格型号":"260*270*1.9","厚度":"1.9mm","内径":"Φ260mm","外径":"Φ270mm","长度":"0mm","宽度":"5mm","材质":"聚四氟乙烯","使用寿命":"730天","特殊要求":"开口方式为斜开口","参照标准":"JB/T 10688-2020","备注":"1、到货附产品合格证及材质证明 2、到货与技术要求不符，厂家免费给予退换货"} |
| O型密封圈 | 459.3*5.7 | 30.00 | 个 | {"规格型号":"459.3*5.7","内径":"Φ459.3mm","外径":"Φ470.7mm","丝径":"Φ5.7mm","材质":"丁腈橡胶","硬度要求":"Shore A 70±5","工作温度":"80℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| O型密封圈 | 609*5.7 | 30.00 | 个 | {"规格型号":"609*5.7","内径":"Φ609mm","外径":"Φ620.4mm","丝径":"Φ5.7mm","材质":"丁腈橡胶","硬度要求":"Shore A 70±5","工作温度":"80℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| O型密封圈 | AG260 | 56.00 | 个 | {"规格型号":"AG260","内径":"Φ260mm","外径":"Φ271.4mm","丝径":"Φ5.7mm","材质":"丁腈橡胶","硬度要求":"Shore A 70±5","工作温度":"80℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| O型密封圈 | P175-175*8.4 | 20.00 | 个 | {"规格型号":"P175-175*8.4","内径":"Φ175mm","外径":"Φ191.8mm","丝径":"Φ8.4mm","材质":"丁腈橡胶","硬度要求":"Shore A 70±5","工作温度":"80℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| 挡圈 | 175*190*1.9 | 36.00 | 个 | {"规格型号":"175*190*1.9","厚度":"1.9mm","内径":"Φ175mm","外径":"Φ190mm","长度":"0mm","宽度":"7.5mm","材质":"聚四氟乙烯","使用寿命":"730天","特殊要求":"斜开口","参照标准":"JB/T 10688-2020","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| 梅花垫 | GR75 | 3.00 | 个 | {"规格型号":"GR75","外径":"158mm","内孔直径":"80mm","厚度":"30mm","瓣数":"10","爪瓣形状":"GR型","材质":"聚氨酯","使用寿命":"180天","参照标准":"GB/T 5272-2017","备注":"到货验收:到货满足相关尺寸参数要求,包装完好,外观完好无损,带有合格证.若到货到物品不符合技术要求或质量不合格,供货商必须无条件予以退换货,由此产生的费用由供货商承担。"} |
| EU型密封 | EU 32 | 20.00 | 个 | {"规格型号":"EU 32","材质":"聚氨酯 PU","工作温度":"80℃","特殊要求":"试用压力8bar；硬度：邵氏A 90±3","使用寿命":"365天"} |
| O型密封圈 | 196.44*3.53/viton/70 | 20.00 | 个 | {"规格型号":"196.44*3.53/viton/70","内径":"Φ196.44mm","外径":"Φ203.5mm","丝径":"Φ3.53mm","材质":"viton","硬度要求":"70邵氏A","工作温度":"90℃","使用寿命":"270天","参照标准":"GB/T 3452.1-2005","备注":"到货质量不符，退换货处理"} |
| O型密封圈 | 37*3.5 | 100.00 | 个 | {"规格型号":"37*3.5","内径":"37mm","外径":"Φ0","丝径":"0","材质":"丁腈橡胶","使用寿命":"6个月"} |
| O型密封圈 | P190-190*5.7 | 72.00 | 个 | {"规格型号":"P190-190*5.7","内径":"Φ190mm","外径":"Φ201.4mm","丝径":"Φ5.7mm","材质":"丁腈橡胶","硬度要求":"Shore A 70±5","工作温度":"80℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"验收标准：需完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间产生的费用由供货商承担。"} |
| 编织风管 | Φ13（内径）*20米（长度） | 30.00 | 米 | {"型号":"Φ13（内径）*20米（长度）","材质":"线编/橡胶","内径":"Φ13mm","外径":"Φ20mm","高度":"0","使用介质":"压缩空气","工作压力":"0.4-1MPa","参照标准":"GB/T 19090-2003"} |
| 测压软管 | DN6*1500 | 10.00 | 个 | {"型号":"DN6*1500","图号":"无","材质":"耐油橡胶","接头材质":"镀锌碳钢","接头尺寸":"公制内螺纹M16*1.5","接头形式":"双头压扣活接头","长度":"1500mm","压力":"15MPa","所属设备名称":"1+4轧机","设备型号":"2350mm","设备生产厂家":"IHI","国产/进口":"国产","使用寿命":"480天","特殊要求":"软管要求内附2层夹布,外层橡胶包覆","参照标准":"JB/T 8727-2017","备注":"系统测压,泄压,排气使用;"} |
| 化学喷雾钢丝缠绕管 | DN25 | 10.00 | 米 | {"规格":"DN25","连接形式":"卡箍连接","工作温度":"-20~100℃","工作压力":"1Mpa","壁厚":"≥4.5mm","内径":"25mm","外径":"≥34mm","参照标准":"GB/T 9574-2017","备注":"要求：每卷长度大于等于50米.\n材质：内胶：白色、光滑，超高分子量交联聚乙烯；增强层：高强力合成线绳及抗静电铜丝；外胶：蓝色、光滑（表面布纹）EPDM特殊合成橡胶。\n使用液体：酸液、碱液、食品级涂料等。\n使用寿命：大于1年\n到货要求：必须提供合格证明，若产品达不到要求，供应商无偿进行换货或退货。"} |
| 金属软管 | DN100*1800mm/法兰连接 | 2.00 | 根 | {"规格型号":"DN100*1800mm/法兰连接","公称直径":"100mm","公称压力":"1Mpa","长度":"1800±5mm","连接件形式":"法兰连接","材质":"钢丝编织波纹管","特殊要求":"法兰一端固定、一端可转动；压力等级1.0Mpa;固定孔：Φ18㎜；****中心圆直径：180mm，厚度22㎜；安装孔数8个。","使用寿命":"365天","参照标准":"GB/T 14525-2010","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 液压密封包 | 70/50*38 | 64.00 | 套 | {"规格型号":"70/50*38","长度":"70mm","宽度":"50mm","高度":"45mm","材质":"聚四氟乙烯添加青铜粉;氟橡胶","工作温度":"90℃","工作介质":"无渍液压油CLOA22","特殊要求":"弯辊缸尺寸70/50*38","使用寿命":"180天","参照标准":"GB/T 32217-2015","备注":"液压密封包组件为;四氟支撑环2个85*91.2*1.7;O型圈1个D85*4;四氟支撑环1个78.8*85*1;O型圈1个D77*4;轴用导向环1个9.7*2.5(Ф50S);孔用导向环1个9.7*2.5(Ф70K);轴用格莱圈一组(Ф50S);孔用格莱圈一组(Ф70K);防尘圈1个(Ф50S)WD****500-N9;到货件必须满足弯辊缸正常使用;不符合技术要求;供货商无条件进行退换货;产生费用均由供货商承担;"} |
| 骨架油封 | 480*530*22 | 15.00 | 个 | {"规格型号":"480*530*22","内径":"Φ480mm","外径":"Φ530mm","高度":"22mm","骨架材质":"45#钢","密封材质":"氟橡胶","结构形式":"V形唇口","工作温度":"120℃","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"到货验收标准:1.支撑辊轴承箱使用，包装完好,内部备件无破碎和损坏，提供合格证；\n2.型号,参数等必须符合技术要求；\n3.升级型号的或替代型号的备件应带有升级或替代证明；\n4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担。"} |
| 骨架油封 | TC110x140x14 | 20.00 | 个 | {"规格型号":"TC110x140x14","内径":"Φ110mm","外径":"Φ140mm","高度":"14mm","骨架材质":"45#钢","密封材质":"改性橡胶","结构形式":"双唇油封","工作温度":"120℃","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"到货验收标准:1.支撑辊轴承箱使用，包装完好,内部备件无破碎和损坏，提供合格证；\n2.型号,参数等必须符合技术要求；\n3.升级型号的或替代型号的备件应带有升级或替代证明；\n4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担。"} |
| 骨架油封 | 160*190*16 | 30.00 | 个 | {"规格型号":"160*190*16","内径":"Φ160mm","外径":"Φ190mm","高度":"16mm","骨架材质":"45#钢","密封材质":"氟橡胶","结构形式":"V形唇口","工作温度":"120℃","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"到货验收标准:1.工作辊轴承箱使用，包装完好,内部备件无破碎和损坏，提供合格证；\n2.型号,参数等必须符合技术要求；\n3.升级型号的或替代型号的备件应带有升级或替代证明；\n4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担。"} |
| 骨架油封 | 180*210*16 | 30.00 | 个 | {"规格型号":"180*210*16","内径":"Φ180mm","外径":"Φ210mm","高度":"16mm","骨架材质":"45#钢","密封材质":"氟橡胶","结构形式":"V形唇口","工作温度":"120","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"到货验收标准:1.工作辊轴承箱使用，包装完好,内部备件无破碎和损坏，提供合格证；\n2.型号,参数等必须符合技术要求；\n3.升级型号的或替代型号的备件应带有升级或替代证明；\n4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担。"} |
| 不锈钢金属编织软管 | DN50*1500 | 5.00 | 根 | {"规格型号":"DN50*1500","公称直径":"50mm","公称压力":"1.6Mpa","长度":"1500mm","连接件形式":"螺纹连接","材质":"接头材质:304不锈钢;软管:304不锈钢","特殊要求":"接头螺纹尺寸：M52*2；锥面密封；每根管配带氟橡胶O型圈","使用寿命":"365天","参照标准":"GB/T 14525-2010","备注":"验收标准：附有产品合格证，供货质量如若与附件要求不匹配，厂家或商家无条件进行退换货，费用由供货商全部承担。"} |
| 骨架油封 | 200*238*17 | 30.00 | 个 | {"规格型号":"200*238*17","内径":"Φ200mm","外径":"Φ238mm","高度":"17mm","骨架材质":"45#钢","密封材质":"氟橡胶","结构形式":"外露骨架W型","工作温度":"120℃","使用寿命":"180天","参照标准":"GB/T 13871.1-2007","备注":"到货验收标准:1.包装完好,内部备件无破碎和损坏.2.型号,参数等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 胶管总成 | 1S-25-750 | 2.00 | 根 | {"型号":"1S-25-750","图号":"无","材质":"内外层为合成橡胶，一层钢丝","接头材质":"碳钢","接头尺寸":"M36*2","接头形式":"公制内螺纹","长度":"750mm","压力":"10bar","所属设备名称":"铝箔轧机","设备型号":"ф280/850*2000","设备生产厂家":"阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"无","参照标准":"JB/T 8727-2017","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 胶管总成 | 1S-8-900 | 4.00 | 根 | {"型号":"1S-8-900","图号":"无","材质":"内外层为合成橡胶，一层钢丝","接头材质":"碳钢","接头尺寸":"M16*1.5","接头形式":"公制内螺纹","长度":"900mm","压力":"10bar","所属设备名称":"铝箔轧机","设备型号":"ф280/850*2000","设备生产厂家":"阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"无","参照标准":"JB/T 8727-2017","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 胶管总成 | 1S-20-1100 | 6.00 | 根 | {"型号":"1S-20-1100","图号":"无","材质":"内外层为合成橡胶，一层钢丝","接头材质":"碳钢","接头尺寸":"M30*2","接头形式":"公制内螺纹","长度":"1100mm","压力":"10bar","所属设备名称":"铝箔轧机","设备型号":"ф280/850*2000","设备生产厂家":"阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"无","参照标准":"JB/T 8727-2017","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 胶管总成 | 2S-20-800 | 4.00 | 根 | {"型号":"2S-20-800","图号":"无","材质":"内外层为合成橡胶，二层钢丝","接头材质":"碳钢","接头尺寸":"M36*2","接头形式":"公制内螺纹","长度":"800mm","压力":"100bar","所属设备名称":"铝箔轧机","设备型号":"ф280/850*2000","设备生产厂家":"阿亨巴赫","国产/进口":"国产","使用寿命":"365天","特殊要求":"无","参照标准":"JB/T 8727-2017","备注":"到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 聚氨酯板 | 1400*250*20 | 100.00 | 块 | {"规格型号":"1400*250*20","材质":"聚氨酯","使用寿命":"6月","特殊要求":"长：1400mm；宽：250mm；厚：20mm，硬度：邵氏85~90"} |
| 缓冲垫 | 内径":"24mm","外径":"43m | 100.00 | 个 | {"内径":"24mm","外径":"43mm","厚度":"10mm","材质":"橡胶","使用寿命":"≥1年","参照标准":"GB 5272-2002"} |
| 不锈钢丝编织软管 | DN15/L50 | 20.00 | 根 | {"规格型号":"DN15/L50","公称直径":"15mm","公称压力":"1Mpa","长度":"500mm","材质":"螺帽和内芯为黄铜，产品外层为304不锈钢丝编织网，内管为EPDM橡胶，垫片为NBR橡胶","使用寿命":"≥2年"} |
| 阻火密封包 | 380*120 | 100.00 | 包 | {"规格型号":"380*120","材质":"内含珍珠岩，蛭石；","尺寸":"380*120","表面处理":"外包装：阻燃布","使用寿命":"1825天","特殊要求":"封口无泄漏","参照标准":"GB 23864-2009","备注":"验收标准：1、包装完好无破损 2、材质、尺寸、参照标准等必须符合技术要求 3、不合格品处理标准：不符合验收标准，不合格产品退换货处理，退换货产生的费用，由供货方承担。"} |
| 氯气胶管 | 2*19*8000 | 6.00 | 根 | {"型号":"2*19*8000","材质":"**乙丙橡胶","内径":"Φ19mm","外径":"Φ26mm","高度":"8000mm","颜色":"黑色","使用介质":"氯气","工作压力":"1Mpa","参照标准":"GB/T 3683-2011","备注":"使用寿命180天，到货后不合格免费退换货"} |
| PVC钢丝增强软管 | DN32*5 | 200.00 | 米 | {"规格":"DN32*5","工作温度":"≤70","工作压力":"-0.1~1.2","壁厚":"5mm","内径":"Φ32mm","外径":"Φ42mm","参照标准":"GB/T 5567-2013"} |
| 高压软管 | 2SP*13*1200 | 5.00 | 根 | {"型号":"2SP*13*1200","材质":"丁腈橡胶+二层钢丝缠绕","接头材质":"Q235","接头尺寸":"M24*1.5","接头形式":"螺纹","长度":"1200mm","压力":"27.5Mpa","国产/进口":"国产","使用寿命":"365天","特殊要求":"两直头，两端均为锥口，锥口直径：16mm","参照标准":"JB/T 8727-2017"} |
| 高压软管 | 2SP*13*500 | 4.00 | 根 | {"型号":"2SP*13*500","材质":"丁腈橡胶+二层钢丝缠绕","接头材质":"Q235","接头尺寸":"M24*1.5","接头形式":"螺纹","长度":"500mm","压力":"27.5Mpa","国产/进口":"国产","使用寿命":"365天","特殊要求":"两直头，两端均为锥口，锥口直径：16mm","参照标准":"JB/T 8727-2017"} |
| 油管 | HA8*3850+FPM SN756 | 20.00 | 根 | {"型号":"HA8*3850+FPM SN756","图号":"无","材质":"耐油合成橡胶，附钢丝编织，外附保护性橡胶。","接头材质":"碳钢","接头尺寸":"螺帽M20*1.5，管两头为压制","接头形式":"油管两端接头：24°锥密封直通管接头带O型圈，通径8mm。","长度":"3850mm","压力":"5MPa","所属设备名称":"1+5热精轧机工作辊轴承座","设备型号":"A00624.****.02-06.5380","设备生产厂家":"德国SMS","国产/进口":"国产","使用寿命":"365天","特殊要求":"①型号解释：HA8*3850--油管两端接头：24°锥密封直通管接头带O型圈（螺帽M20*1.5），管两头为压制，通径: 8mm，油管长度：3850mm。FPM--O型圈材质：FPM(氟橡胶)，SN756--产品结构：内胶层，中胶层，增强层，外胶层。②油管材质：耐油合成橡胶，附钢丝编织，外附保护性橡胶。③接头材质：碳钢。④耐抗压、柔软度高.工作压力5MPa.工作温度70摄氏度。⑤如果供应商供货与提报计划不符.要求供应商调换货，如果因质量问题造成损失由供货商负责。","参照标准":"GB/T 10826.4-2008","备注":"①型号解释:HA8*3850--油管两端接头:24°锥密封直通管接头带O型圈（螺帽M20*1.5）,管两头为压制,通径:8mm,油管长度:3850mm.FPM--O型圈材质:FPM(氟橡胶),SN756--产品结构:内胶层,中胶层,增强层,外胶层.②油管材质:耐油合成橡胶,附钢丝编织,外附保护性橡胶.③接头材质:碳钢.④耐抗压,柔软度高,工作压力5MPa,工作温度70摄氏度.⑤如果供应商供货与提报计划不符,要求供应商调换货,如果因质量问题造成损失由供货商负责."} |
| 油管 | HA6*3850+FPM SN756 | 20.00 | 根 | {"型号":"HA6*3850+FPM SN756","图号":"无","材质":"耐油合成橡胶，附钢丝编织，外附保护性橡胶","接头材质":"碳钢","接头尺寸":"螺帽M18*1.5，管两头为压制","接头形式":"油管两端接头：24°锥密封直通管接头带O型圈（螺帽M18*1.5，管两头为压制），通径: 6mm","长度":"3850mm","压力":"5MPa","所属设备名称":"1+5热精轧机工作辊轴承座","设备型号":"A00624.****.02-06.5380","设备生产厂家":"德国SMS","国产/进口":"进口","使用寿命":"365天","特殊要求":"①型号解释：HA6*3850--油管两端接头：24°锥密封直通管接头带O型圈（螺帽M18*1.5，管两头为压制），通径: 6mm，油管长度：3850mm。FPM--O型圈材质：FPM(氟橡胶)，SN756--产品结构：内胶层，中胶层，增强层，外胶层。②油管材质：耐油合成橡胶，附钢丝编织，外附保护性橡胶。接头材质：碳钢。③耐抗压、柔软度高、工作压力5MPa、工作温度70摄氏度。④如果供应商供货与提报计划不符，要求供应商调换货，产生的费用由厂家承担，如果因质量问题造成损失由供货商负责。","参照标准":"GB/T 10826.4-2008","备注":"①型号解释：HA6*3850--油管两端接头：24°锥密封直通管接头带O型圈（螺帽M18*1.5，管两头为压制），通径: 6mm，油管长度：3850mm。FPM--O型圈材质：FPM(氟橡胶)，SN756--产品结构：内胶层，中胶层，增强层，外胶层。\n②油管材质：耐油合成橡胶，附钢丝编织，外附保护性橡胶。\n接头材质：碳钢\t\n③耐抗压、柔软度高、工作压力5MPa、工作温度70摄氏度。\n④如果供应商供货与提报计划不符.要求供应商调换货，产生的费用由厂家承担，如果因质量问题造成损失由供货商负责。"} |
| 蛇皮水管 | Φ25 | 100.00 | 米 | {"规格":"Φ25"} |
| 油封 | UHS53*63*6 | 20.00 | 个 | {"规格型号":"UHS53*63*6","内径":"Φ53mm","外径":"Φ63mm","密封圈高度":"6mm","唇口高度":"6mm","唇形":"Y","材质":"聚氨酯","工作温度":"-10~90℃","使用寿命":"180天","参照标准":"GB/T 9877-2008","备注":"如不符合技术要求供应商予以无条件退换货处理"} |
| 高压油管 | H3SHΦ8*750/56.0Mpa | 1.00 | 根 | {"型号":"H3SHΦ8*750/56.0Mpa","图号":"无","材质":"3SH软管,内管为黑色耐油橡胶,中间为3层高抗拉强度钢丝缠绕层,表皮为黑色耐油橡胶.","接头材质":"碳钢","接头尺寸":"24°/M16*1.5*S19","接头形式":"24°锥O型圈密封胶管接头（轻型系列）","长度":"750mm","压力":"56.0mpa","所属设备名称":"80MN拉伸机","设备型号":"HC-HB-LSJ-01","设备生产厂家":"****公司","国产/进口":"进口","使用寿命":"365天","特殊要求":"油管自带O型圈,O型圈材质:丁晴橡胶.适应温度-20℃~+70℃.","参照标准":"JB/T 8727-2017","备注":"无品牌要求,验收标准:到货外包装无破损;划伤;油管两端有防尘堵头,到货必须附带检验报告及合格证;管接头尺寸及管身标注压力与合格证一致.不合格处理方法:若到货质量与技术要求不符;换货至退货处理,产生的费用由供货商承担."} |
| 水管 | φ40 | 90.00 | 米 | {"型号":"φ40","材质":"天然橡胶","内径":"Φ40mm","外径":"Φ54mm","高度":"0mm","颜色":"黑色","使用介质":"生活水","工作压力":"1Mpa","参照标准":"GB/T 1186-2016","备注":"使用寿命：≥60天，压力要求：1兆帕，内径：40mm，外径：54mm验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} |
| 同轴高温软管 | 1/4 -1/4\" M5 | 30.00 | 根 | {"型号":"1/4 -1/4\" M5.2","材质":"管接头为碳钢，内外管为四氟。","内径":"Φ12mm","外径":"Φ30mm","高度":"5200mm","颜色":"不限定","使用介质":"内层流通工艺防锈油，夹层流通导热油。","工作压力":"1Mpa","参照标准":"GB/T 10544-2022","备注":"此同轴高温软管使用在涂油机，最高使用温度110度，使用寿命不低于6个月，要求需要耐温、耐油，且在坦克链内反复弯曲动作使用。上述描述高度5200mm即管**度M5.2。原理图见图一所示：两个蓝色的标记为工艺油进出口，尺寸为1/4寸卡套式接头见上图。两个红色标记为导热油进出口，尺寸为1/4寸锥口外螺纹见上图，红色标记的导热油在夹层里流通，作用为给中间流通的工艺油伴热保证工艺油的使用温度。外圈需要有橡胶和尼龙编制的保温保护层。软管到货后需要4个油口均有防尘措施，防止异物进入。加工制作时，现场可以提供此胶管的样品进行详细测绘及研究。如到货不符上述技术要求或现场使用工况，厂家进行重新加工制作，所产生的相关费用由厂家承担。"} |
| 连退挡水环 | 宽度":"260mm","厚度":"14 | 100.00 | 套 | {"宽度":"260mm","厚度":"14mm","材质":"**乙丙橡胶","适用压力":"0.3Mpa","适用温度":"≤70℃","使用寿命":"365天","特殊要求":"耐酸碱、耐油、橡胶硬度ShoreA60","参照标准":"GB/T 5574-2008","备注":"1.外径：260±2mm、内径：123+1mm、外端厚度：5±0.5mm、内端厚度：14±1.4mm\n2.粗糙度：Ra3.2\n3.表面不允许有开裂、穿孔等影响使用性能的缺陷。对于其他不影响使用性能的缺陷，每处缺陷深度不超过产品厚度的1/10，最深不超过2mm，缺陷面积不超过1cm2，每平方米内缺陷不得超过3处，整件产品不超过5处。\n4..到货验收:到货需附带检验报告,如到货质量与技术要求不符,退换货处理,产生费用由供货商承担。历史编码：无"} |
| 尼龙阻燃波纹管 | BG-23NBV0（3/4”） | 1700.00 | 米 | {"型号":"BG-23NBV0（3/4”）","规格尺寸":"外表直径28.5±0.5mm，内部直径：23±0.5mm，其外表和内部均为波浪形，管壁厚度为：1±0.1mm","颜色":"黑色","配套参数":"柔软有韧性，抗扭曲，弯曲性能好，可以承受较重的负载可以承受脚踩的重压，不断裂，不变形，可以迅速恢复，并且本身无任何损伤","使用温度":"-40℃-+125℃","产品材质":"PA6 尼龙","参照标准":"JT/T 1031-2016","备注":"使用寿命：2年，国产/进口信息：国产\n验货标准：1、由于产品升级或停产导致设备型号不一致，但接口尺寸、安装方式等参数满足技术要求，设备厂家出证明入库。\n2、外观破损、变形退货。"} |
| O型密封圈 | 70*3 | 100.00 | 个 | {"规格型号":"70*3","内径":"Φ70mm","外径":"Φ76mm","丝径":"Φ3mm","材质":"氟橡胶","硬度要求":"70IRHD","工作温度":"-20~80℃","使用寿命":"180天","参照标准":"GB/T 3452.1-2005","备注":"1、无品牌要求，备件外观包装良好，密封整体平整光滑，无裂边毛刺凹凸现象，各项加工尺寸符合技术要求，否则进行退换货处理，因此产生的损失由供货商承担。\n2、备件到货附带出厂产品合格证及材质检验报告。"} |
| O型密封圈 | 405.26*7/viton/70 | 30.00 | 个 | {"规格型号":"405.26*7/viton/70","内径":"Φ405.26mm","外径":"Φ419.26mm","丝径":"Φ7mm","材质":"viton","硬度要求":"70邵氏A","工作温度":"90℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"备件到货附带出厂产品合格证，无裂边毛刺凹凸现象，各项加工尺寸符合技术要求，否则进行退换货处理，因此产生的损失由供货商承担。"} |
| O型密封 | 315*5.33 | 20.00 | 个 | {"规格型号":"315*5.33","内径":"Φ315mm","外径":"Φ325.66mm","丝径":"Φ5.33mm","材质":"FKM","硬度要求":"70邵氏A","工作温度":"90℃","使用寿命":"270天","参照标准":"GB/T 3452.1-2005","备注":"备件到货附带出厂产品合格证，无裂边毛刺凹凸现象，各项加工尺寸符合技术要求，否则进行退换货处理，因此产生的损失由供货商承担。"} |
| O型圈 | 9.5*2.5 | 100.00 | 个 | {"规格型号":"9.5*2.5","内径":"Φ9.5mm","外径":"Φ14.5mm","丝径":"Φ2.5mm","材质":"FKM","硬度要求":"70邵氏A","工作温度":"90℃","使用寿命":"365天","参照标准":"GB/T 3452.1-2005","备注":"备件到货附带出厂产品合格证，O型圈整体平整光滑，无裂边毛刺凹凸现象，各项加工尺寸符合技术要求，否则进行退换货处理，因此产生的损失由供货商承担。"} |
| 胶管 | DN2*1500/M16*2 | 50.00 | 根 | {"型号":"DN2*1500/M16*2","图号":"无","材质":"芯管及外表PA(聚酰胺),压力承受物合成纤维","接头材质":"锌镍镀层","接头尺寸":"M16*2","接头形式":"带有顶针式接头","长度":"1500mm","压力":"允许工作压力400bar,爆破压力1100bar","所属设备名称":"无","设备型号":"无","设备生产厂家":"无","国产/进口":"国产","使用寿命":"365天","特殊要求":"所用材质必须具有良好的耐轧制油及阻燃性","参照标准":"JB/T 6143.2-2007","备注":"验收要求：到货不符合技术要求退换货处理"} |
| 高弹橡胶板 | 3mm | 100.00 | 千克 | {"规格型号":"3mm","厚度":"3mm","宽度":"1000mm","材质":"**乙丙橡胶","耐油性能":"不耐油","硬度要求":"H4~H6","抗撕裂性能":"Ts","拉断强度":"5Mpa","拉伸强度":"≥4Mpa","使用寿命":"730天","特殊要求":"表面应平滑，不允许有疙瘩、裂缝、气泡，外来杂质和其他对使用有影响的缺陷","参照标准":"GB/T 5574-2008","备注":"发现所供备件不符合本要求，供应商应无条件更换符合技术要求的备件"} |
| 铣床翻转机垫块 | 长度":"1067mm","宽度":"1 | 8.00 | 块 | {"长度":"1067mm","宽度":"130mm","高度":"35mm","验收":"当验收不符合技术要求时，需进行退换货处理，期间所产生的运输费用由供货商承担","材质":"尼龙","参照标准":"DB13/T 2071-2014","备注":"寿命≥1年。"} |
| 骨架油封 | 65*80*8 | 8.00 | 个 | {"规格型号":"65*80*8","内径":"Φ65mm","外径":"Φ80mm","高度":"8mm","骨架材质":"低碳钢","密封材质":"丁腈橡胶双唇油封","结构形式":"双唇油封，并在唇部装有箍圈式连接的弹簧","工作温度":"-15~120℃","使用寿命":"不小于730天","参照标准":"GB/T 9877-2008","备注":"1、备件外观包装良好，油封整体平整光滑，无裂边毛刺凹凸现象，各项加工尺寸符合技术要求，否则进行退换货处理，因此产生的损失由供货商承担。\n2、备件到货附带出厂产品合格证及材质检验报告"} |
| 液压管 | DN20*2000（两端直头） | 20.00 | 根 | {"型号":"DN20*2000（两端直头）","材质":"胶管为4层钢丝编织胶管，胶管材质为橡胶，接头材质为碳钢","内径":"Φ20mm","外径":"Φ40mm","高度":"2000mm","颜色":"黑色","使用介质":"46号液压油","工作压力":"20Mpa","参照标准":"JB/T 8727-2017","备注":"油管接头形式为：24度锥形口接头，接头为1/2英寸管螺纹，扳手空间为46mm，接口处螺纹尺寸及扳手空间见物资图片，产品无破损，配带密封防尘罩并附带合格证明。液压管为两个直头，4层加强钢丝编制，耐压超过20兆帕。公称通径为20mm，外径大于40mm，上述描述油管高度即油管长度，为2000mm。使用寿命不低于1年，如果到货不符，产生退换货费用，厂家承担。"} |
| 精轧工作辊轴承座水封 | VA600 | 72.00 | 个 | {"规格型号":"VA600","内径":"Φ540mm","外径":"Φ570mm","厚度":"Φ25mm","材质":"氟橡胶","硬度要求":"邵氏40°-80°","工作温度":"40-80℃","特殊要求":"表面要光洁,无毛边，耐油、耐高温、耐酸碱、密封性好","使用寿命":"365天","参照标准":"GB/T 6994-2007","备注":"验收标准：完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间所产生的费用由厂家自行承担。"} |
| 精轧轴承座内侧无骨架油封 | 530*580*22 | 60.00 | 个 | {"规格型号":"530*580*22","内径":"Φ530mm","外径":"Φ580mm","厚度":"Φ22mm","材质":"氟橡胶","硬度要求":"邵氏70°-90°","工作温度":"40-80℃","特殊要求":"棕色氟胶,表面要光洁,无毛边,耐油、耐高温、耐酸碱、密封性好","使用寿命":"365天","参照标准":"GB/T 13871.1-2022","备注":"验收标准：完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间所产生的费用由厂家自行承担。"} |
| 精轧轴承座外侧无骨架油封 | 455*505*25 | 60.00 | 个 | {"规格型号":"455*505*25","内径":"Φ455mm","外径":"Φ505mm","厚度":"Φ25mm","材质":"氟橡胶","硬度要求":"邵氏70°-90°","工作温度":"40-80℃","特殊要求":"棕色氟胶,表面要光洁,无毛边,耐油、耐高温、耐酸碱、密封性好","使用寿命":"365天","参照标准":"GB/T 13871.1-2022","备注":"验收标准：完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间所产生的费用由厂家自行承担。"} |
| 粗轧工作辊轴承座无骨架油封 | 850*924*25 | 48.00 | 个 | {"规格型号":"850*924*25","内径":"Φ850mm","外径":"Φ924mm","厚度":"Φ25mm","材质":"氟橡胶","硬度要求":"邵氏70°-90°","工作温度":"40-80℃","特殊要求":"棕色氟胶,表面要光洁,无毛边,耐油、耐高温、耐酸碱、密封性好","使用寿命":"365天","参照标准":"GB/T 13871.1-2022","备注":"验收标准：完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间所产生的费用由厂家自行承担。"} |
| 粗轧工作辊轴承座水封 | VA950 | 12.00 | 个 | {"规格型号":"VA950","内径":"Φ865mm","外径":"Φ895mm","厚度":"Φ25mm","材质":"氟橡胶","硬度要求":"邵氏40°-80°","工作温度":"40-80℃","特殊要求":"表面要光洁,无毛边，耐油、耐高温、耐酸碱、密封性好","使用寿命":"365天","参照标准":"GB/T 6994-2007","备注":"验收标准：完全符合上述技术要求，并提供出厂检测报告或合格证；如与技术要求不符，需退换货处理，期间所产生的费用由厂家自行承担。"} |
| 液压缸密封 | PN125HM001/RG2HMO701 | 1.00 | 套 | {"规格型号":"PN125HM001/RG2HMO701","材质":"丁腈橡胶、铜、邵氏A、聚氨酯","工作温度":"-5~70℃","工作介质":"油","使用寿命":"365天","备注":"其为PN125/70型液压缸密封，请区别于PN125/56型。"} |
| 无编织网金属波纹软管 | 40*250 | 5.00 | 根 | {"规格型号":"40*250","公称直径":"40mm","公称压力":"1.6Mpa","长度":"250mm","连接件形式":"螺纹连接","材质":"接头材质:304不锈钢;波纹管:304不锈钢","特殊要求":"接头螺纹尺寸：G11/2，平面密封；每根管配带四氟垫","使用寿命":"365天","参照标准":"GB/T 14525-2010","备注":"验收标准：附有产品合格证，供货质量如若与附件要求不匹配，厂家或商家无条件进行退换货，费用由供货商全部承担。"} |
| 密封包 | 160/100 | 3.00 | 套 | {"规格型号":"160/100","长度":"0mm","宽度":"0mm","高度":"0mm","材质":"斯特封、格莱圈是由PTFE材质与氟橡胶O形圈的组合密封圈；导向环、支承环由聚四氟乙烯；O形圈、防尘圈、轴用圈材质氟橡胶","工作温度":"60℃","工作介质":"煤油","特殊要求":"工作压力:100 bar；缸径：160mm；活塞杆直径：100mm","使用寿命":"365天","参照标准":"GB/T 10708.3-2000、GB/T 10708.1-2000、GB/T 3452.1-2005","备注":"密封包\\160/100\\0mm\\0mm\\0mm\\斯特封、格莱圈是由PTFE材质与氟橡胶O形圈的组合密封圈；导向环、支承环由聚四氟乙烯；O形圈、防尘圈、轴用圈材质氟橡胶\\60℃\\煤油\\工作压力:100 bar；缸径：160mm；活塞杆直径：100mm\\365天\\GB/T 10708.3-2000、GB/T 10708.1-2000、GB/T 3452.1-2005\\助卷器液压缸密封包\\防尘圈LBH 90*100*6*8\\轴用圈90*100*7\\支承环90*95*15\\斯特封 90*105.5*6.3\\O型圈内径118*5.3\\O型圈内径73*3.55\\格莱圈160*139*8.1\\支承环160*155*15\n到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 液压油管 | M36*2*1200 | 12.00 | 根 | {"型号":"M36*2*1200","图号":"无","材质":"胶管为2层钢丝编织胶管，O型圈为丁腈橡胶","接头材质":"接头材质为钢","接头尺寸":"M36*2","接头形式":"24°锥O型圈密封胶管接头（重型系列），两端均为内丝螺纹连接，软管一端为0°直通接头，另端一为90度直接头。内螺纹M36，螺距2","长度":"1200mm±10mm","压力":"10Mpa","所属设备名称":"铝箔轧机","设备型号":"1700铝箔轧机","设备生产厂家":"涿神","国产/进口":"国产","使用寿命":"365天","特殊要求":"两层钢丝编织层和厚外覆层油管，油管自带O型圈。适应温度：-10℃-80℃","参照标准":"GB/T 3683-2023","备注":"用于上下支撑辊轴承箱冷却循环。无品牌要求,验收标准:到货外包装无破损;无划伤，油管两端有防尘堵头,到货必须附带检验报告及合格证,管接头尺寸及管身标注压力与合格证一致,不合格处理方法：若到货质量与技术要求不符,换货至退货处理,产生的费用由供货商承担."} |
| 胶管 | 4HA20*1350 | 20.00 | 根 | {"型号":"4HA20*1350","图号":"无","材质":"四层钢丝缠绕的橡胶软管","接头材质":"碳钢","接头尺寸":"M36*2","接头形式":"24°锥密封","长度":"1350","压力":"290bar","所属设备名称":"SMS精轧机","设备型号":"3100","设备生产厂家":"SMS","国产/进口":"国产","使用寿命":"365天","特殊要求":"无品牌要求,验收标准:到货外包装无破损;划伤，油管两端有防尘堵头,到货必须附带检验报告及合格证,管接头尺寸及管身标注压力与合格证一致,不合格处理方法：若到货质量与技术要求不符,换货至退货处理,产生的费用由供货商承担.","参照标准":"GB/T 3683-2023","备注":"胶管\\4HA20*1350\\-\\四层钢丝缠绕的橡胶软管\\碳钢\\M36*2\\24°锥密封\\-\\-\\-\\-\\-\\-\\365天\\-\\-\\-"} |
| 投标厂商资质 | |||
| 注册资金 | 专业资质 | ||
| 公司业绩 | |||
| 相关认证 | |||
| 其他 | |||
| 联系我们 | |||
| 采购咨询电话 | 0535-****706 | ||
| 地址 | ******集团总部办公楼 | ||
招标进度跟踪
2026-06-16
招标公告
橡胶制品
当前信息
标书代写
招标项目商机
暂无推荐数据
400-688-2000
欢迎来电咨询～
